JS防水涂料

本品是以丙烯酸酯等聚合物乳液和水泥為主要原料，加入其它外加劑制得的雙組份水性建筑防水材料,，兩組份在現場攪拌成均勻,，細膩漿料，涂刷

于基體表面,，固化后可形成柔韌,、高強的防水涂膜。產品具有“剛?cè)嵯酀?jì)”的特性,，既有聚合物涂膜的延伸性,、防水性，也有水硬性膠凝材料強度

高,、耐水性好,、易與潮濕基層粘結的優點。

【性能特點】

1,、水性涂料,，無害，無污染,，屬環保型涂料,。

2、具有一定的延伸性,，對基層變形適應力較強;同時,，具有無機材料耐水，耐老化的物質,。

3,、具有良好的抗?jié)B功能。

4,、防水層上可用砂漿直接粘貼瓷磚,。

5、可在潮濕基層上施工并粘結牢固,。

6,、施工簡單方便，冷施工,，操作方便,，干燥時間短，可縮短工期,。

【適用范圍】

衛生間,、浴室、廚房,、樓地面,、陽臺,、水池及墻面防水和木地板防潮。

【使用要點】

基層：基層應堅硬,、無浮塵,。陰陽角以及管根部等兩面交接處，均應做成圓弧形,，陰角直徑宜大于50mm,，陽角直徑宜大于10mm。

防水層：可單獨做成涂膜防水,，一道設防時,，廁衛間不小于1.5mm，地下工程不小于2.0mm,。

【施工要點】

基層處理：基層應處理平整,、堅實、干凈,、無油跡,、無明顯積水，陰陽角宜為圓弧形,。油污須除干凈,，低凹破損處修平。

【配料】

1,、配料比例：液料：粉料：水=1：1.5：(0～1),，水的添加量可在規定范圍之內適當調節，以調整涂料粘稠度,，滿足立面和平面不同部位的施

工要求,。

2、配料方法：先將液料和水倒入攪拌桶中,，在手提攪拌器不斷攪拌下將粉料徐徐加入其中,，至少攪拌5分鐘，攪拌均勻,，呈漿狀無團塊,。

3、細部附加防水層：按設計要求在留設凹槽內嵌填密封材料,，在陰陽角,、管根等細部應特殊處理，地下工程宜夾鋪一層胎體增強材料,。

4,、大面積防水施工：宜分三遍涂刷，每遍涂膜完全干燥后才可涂下一遍，后遍涂刷方向與前遍涂刷方向垂直,，每遍涂料用量約0.5～1.0kg/平米,。

每遍涂布時間一般間隔4小時，冬季宜延長,。每遍涂膜厚度以0.4～0.5毫米為宜,，不宜一遍過厚。立面施工以不加水或少加水為宜,，以免涂料流淌,，

致使立面厚度不易達到設計厚度，同時導致陰陽角堆積料過厚,，產生裂紋。

5,、涂膜防水層完成并驗收合格后,，進行保護層或飾面層施工。

【參考用量】每毫米厚的涂膜約需產品2.0kg/㎡,。

【產品顏色】粉料：灰白色,。液料：白色或藍色

【涂膜顏色】乳白色或藍色

【注意事項】

1、施工時氣溫須高于5℃,，陰雨天氣室外不宜施工,，基層有明顯積水時不宜施工。

2,、配好的混合料應在3小時內使用完畢,。

3、開封后未使用完的液料或粉料組分,，應密封貯存,，并盡快使用。

4,、每遍施工厚度不能超過1mm,，一次涂刷過厚，涂膜容易產生裂紋,。

5,、立面施工時，以不加水或少加水為宜,，以免涂料流淌,，致使立面厚度不易達到設計厚度，同時導致陰陽角堆積料過厚,，產生裂紋,。

6、防水涂膜應完全干燥后方可進行飾面層施工,。

【包裝,、運輸及貯存】

1,、產品粉料組份和液料組份先用塑料袋分別包裝后再裝入塑料桶中。

2,、運輸按非危險品要求,。運輸時，防止雨淋,、曝曬,、擠壓、碰撞,、倒置,，保持包裝完好無損。運輸過程中環境溫度不能低于0℃,，否則,，應采取

保溫措施。

3,、產品液料組份宜密封存放于5℃以上的陰涼處,，貯存溫度不得低于0℃;粉料須存放于干燥處。

[Product Name] JS Waterproof Coating (18kg)

Features: High tensile strength

High bond strength

Excellent extensibility

Green and eco-friendly

This product is based on acrylic polymer emulsion and cement as the main raw materials, adding other additives to prepare two components of waterborne building waterproof materials, stir two components in the field evenly, and brush fine slurry on the surface of the matrix, and a flexible and high-strength waterproof film can be formed after curing. The product has the characteristics of "hardness and softness", which not only has the extensibility and waterproof property of polymer film, but also has the advantages of high strength, high water resistance, easy to bond with the wet base of hydraulic cementitious materials. [Performance Characteristics] 1. It is a water-based coating, non-toxic, harmless, pollution-free, and belongs to environmental friendly coating. 2. It has certain extensibility and strong adaptability to base deformation; meanwhile, it is a material with water resistance and aging resistance as inorganic materials. 3. It has good impermeability. 4. The waterproof layer can be directly pasted with mortar. 5. It can be constructed on wet base course and bonded firmly. 6. The construction is simple and convenient, cold construction, convenient operation, short drying time and short construction period. [Scope of application] Waterproofness and moisture proofing for toilets, bathrooms, kitchens, floors, balconies, pools and wall and wood floors. [Key points for use] Base: the base should be hard and free of floating dust. The internal and external corners and the junction of the two sides of the pipe root should be made into arc shape, the diameter of the internal angle should be greater than 50 mm, and the diameter of the external angle should be greater than 10 mm.

Waterproof layer: it can be made into film waterproof separately. When one fortification is carried out, the toilet room shall not be less than 1.5mm, and the underground engineering shall not be less than 2.0mm. [Key Points of Construction] Base treatment: the base should be smooth, solid, clean, without oil stains and obvious water accumulation, and the internal and external corners should be circular arc. The oil stain must be cleaned up and the concave and damaged parts should be leveled. [Ingredients] 1. Proportioning ratio: liquid material: Powder: water=1:1.8 (0-1). The amount of water can be adjusted within the specified range to adjust the coating viscosity to meet the application requirements of different parts of fa?ades and planes. 2. Mixing method: Firstly pour the liquid material and water into the mixing bucket, then slowly add the powder into the mixing bucket with the continuous stirring of the hand-held agitator, and stir it for at least 5 minutes, and thoroughly stir it evenly until it becomes a slurry without agglomerations. 3. Additional waterproof layer for details: according to the design requirements, the sealing materials shall be embedded in the reserved grooves, and the internal and external corners, pipe roots and other details shall be specially treated, and a layer of matrix reinforcement material shall be laid in the underground engineering. 4. Large area waterproof construction: it should be painted in three times. After each coating film completely dry can be coated next. The direction of the last coating is perpendicular to the direction of the previous one. The amount of each coating is about 0.5-1.0kg / m2. The coating interval is normally 4 hours and should be extended in winter. The thickness of each coating should be 0.4-0.5 mm, not too thick. , . For facade construction, it is better to add no water or less water to avoid coating flowing and the facade thickness is too thick to reach the design thickness,makingthe internal and external corner accumulation materials, resulting in cracks. 5. After the completion and acceptance of the coating waterproofness, the construction of protective layer or finish layer shall be carried out. [Reference dosage] About 2.0kg / m2 of product is required for each millimeter of coating thickness [Product color] Powder: gray white. Liquid material: milk white [Coating color]White [Precautions] 1. During construction, the air temperature must be higher than 5℃ and outdoor construction is neither suitable in rainy weather, nor suitable for construction when there is obvious water accumulation in the base 2. The mixture should be used up within 3 hours. 3. Unused liquid or powder components after opening shall be sealed and stored and used as soon as possible. 4. The thickness of each construction should not be more than 1 mm. If the coating is too thick at one time, it will be easy to crack. 5. During the facade construction, it is appropriate to add no water or less water so as to avoid the coating flowing, which makes the facade thickness difficult to reach the design thickness, and causes the accumulation material of internal and external corners to be too thick, resulting in cracks. 6. The waterproof coating should be completely dry before finish layer construction. [Packaging, transportation and storage] 1. The powder and liquid components of the product are packed in plastic bags and then put into a plastic barrel. 2. It should be transported according to the requirements of non-dangerous goods. During the transportation, no exposure to rain, sunlight, and no extrusion, collision and inversion, and keep the package intact. During the transportation, the ambient temperature should not be lower than 0℃, otherwise, insulation measures should be taken. 3. The liquid components of the product should be stored in a cool place above 5℃, and the storage temperature should not be lower than 0℃; the powder should be stored in a dry place. Retention period: 12 months Executive standard: GB/T23445-2009

生態友好型

ECO FRIENDLY

100%滿意

100% SATISFACTION

全球服務 互惠共享

GLOBAL SERVICE RECIPRAL SHARING

天樂倩潔國際品牌環保產品

Tianle Qianjie International Brand Environmental Friendly Products